Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
???
10/05/10 06:17
Modified:
  10/05/10 06:26
Read: times


 		 #178912 - My solution
Responding to: ???'s previous message
I was asked by a guy who sells wax pots to solve his problems that heaters keep blowing off.
What I did was instead of making the heater on all the time (when heater is on) I made a simple circuit without zero crossing that turns the heater on for one cycle and turns it back off for another cycle. This way the power to the heater was cut down to a half and the guy tested my circuit for months and he was very happy with the results, so I modified about 50 wax pots for him.
Mahmood

List of 41 messages in thread
TopicAuthorDate
What is the reason for Heater blowing.            01/01/70 00:00      
   Hof often/how we?            01/01/70 00:00      
      Some more information...            01/01/70 00:00      
   continuous rating            01/01/70 00:00      
      This could be the reason...            01/01/70 00:00      
   Way too much current...            01/01/70 00:00      
      Some more information required...            01/01/70 00:00      
   do you have hysteresis in your control?            01/01/70 00:00      
      No there is no hysteresis.            01/01/70 00:00      
         Four pulses?            01/01/70 00:00      
            The Heaters are failing, electronics is OK.            01/01/70 00:00      
               Why Pulses?            01/01/70 00:00      
                  I will do just that...            01/01/70 00:00      
                     Processor must know about zero-crossings            01/01/70 00:00      
               ??            01/01/70 00:00      
                  soft start            01/01/70 00:00      
                     Soft Start            01/01/70 00:00      
                        an easy and interesting check            01/01/70 00:00      
                           Soft start, again...            01/01/70 00:00      
                  Yes these heaters need Soft start            01/01/70 00:00      
                     Again: Power? Voltage? Current?            01/01/70 00:00      
                        Avoid driving gate all the way to next zero crossing            01/01/70 00:00      
                           Crest factor/power factor correction            01/01/70 00:00      
                     Phase angle control...            01/01/70 00:00      
                        I agree with you.            01/01/70 00:00      
                           Good luck!            01/01/70 00:00      
                           are all heating coils the same ?            01/01/70 00:00      
                           There You Go            01/01/70 00:00      
         re the possible need for hysteresis            01/01/70 00:00      
         Power? Voltage? Current?            01/01/70 00:00      
   Alternate Heating Control Algorithm            01/01/70 00:00      
      Some more clarification...            01/01/70 00:00      
         Voltage - or power? [ed]            01/01/70 00:00      
   The other controllers            01/01/70 00:00      
   Thanks All members.            01/01/70 00:00      
   just suggest..            01/01/70 00:00      
      Reply to JecksonS Ben            01/01/70 00:00      
         Good point!            01/01/70 00:00      
            supposed to            01/01/70 00:00      
         opto isolated triac            01/01/70 00:00      
   My solution            01/01/70 00:00      

Back to Subject List