Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
???
09/23/10 07:47
Read: times


 		 #178663 - opto isolated triac
Responding to: ???'s previous message
>>Jecksons Ben said:
>>For me....I consider used the MOC3021 for efficency.Just TRIAC drive by MCU(or transistor when (Gate of >>TRIAC) need more voltage).
>I do NOT want to use it this way. MOC3021 provides the necessary isolation of High voltage from my Micro >controller pins. I Think, this reason is enough to use Opto isolated TRAIC driver.

I miss typed...I meant didn't used MOC3021 for efficiency.

Great reason...Opto isolated TRIAC driver.

There's suggest at Sonsivri.com tell me that CPC1966 or similiar.You could used ports directly from AT89C2051 MCU.

Thank you
Jeckson Ben




List of 41 messages in thread
TopicAuthorDate
What is the reason for Heater blowing.            01/01/70 00:00      
   Hof often/how we?            01/01/70 00:00      
      Some more information...            01/01/70 00:00      
   continuous rating            01/01/70 00:00      
      This could be the reason...            01/01/70 00:00      
   Way too much current...            01/01/70 00:00      
      Some more information required...            01/01/70 00:00      
   do you have hysteresis in your control?            01/01/70 00:00      
      No there is no hysteresis.            01/01/70 00:00      
         Four pulses?            01/01/70 00:00      
            The Heaters are failing, electronics is OK.            01/01/70 00:00      
               Why Pulses?            01/01/70 00:00      
                  I will do just that...            01/01/70 00:00      
                     Processor must know about zero-crossings            01/01/70 00:00      
               ??            01/01/70 00:00      
                  soft start            01/01/70 00:00      
                     Soft Start            01/01/70 00:00      
                        an easy and interesting check            01/01/70 00:00      
                           Soft start, again...            01/01/70 00:00      
                  Yes these heaters need Soft start            01/01/70 00:00      
                     Again: Power? Voltage? Current?            01/01/70 00:00      
                        Avoid driving gate all the way to next zero crossing            01/01/70 00:00      
                           Crest factor/power factor correction            01/01/70 00:00      
                     Phase angle control...            01/01/70 00:00      
                        I agree with you.            01/01/70 00:00      
                           Good luck!            01/01/70 00:00      
                           are all heating coils the same ?            01/01/70 00:00      
                           There You Go            01/01/70 00:00      
         re the possible need for hysteresis            01/01/70 00:00      
         Power? Voltage? Current?            01/01/70 00:00      
   Alternate Heating Control Algorithm            01/01/70 00:00      
      Some more clarification...            01/01/70 00:00      
         Voltage - or power? [ed]            01/01/70 00:00      
   The other controllers            01/01/70 00:00      
   Thanks All members.            01/01/70 00:00      
   just suggest..            01/01/70 00:00      
      Reply to JecksonS Ben            01/01/70 00:00      
         Good point!            01/01/70 00:00      
            supposed to            01/01/70 00:00      
         opto isolated triac            01/01/70 00:00      
   My solution            01/01/70 00:00      

Back to Subject List