Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
???
08/05/09 10:05
Read: times


 		 #168171 - I just found a relay which needs lot lesser current
Responding to: ???'s previous message
Anurag Mishra said:
I just found a relay which needs lot lesser current, and may be used in my application.

Note that it most probably still has the characteristic that its "holding" current is (much) less than its "pull-in" current - so you can still use the techniques described to obtain an even greater reduction...!

:-)

List of 44 messages in thread
TopicAuthorDate
Mechnical Relay or Triac            01/01/70 00:00      
   Relays Or Triacs            01/01/70 00:00      
      Isolation            01/01/70 00:00      
      Relay or Triac            01/01/70 00:00      
         Pull-in vs hold current?            01/01/70 00:00      
         Relays Suggestions            01/01/70 00:00      
      Agree            01/01/70 00:00      
         optotriac            01/01/70 00:00      
            Relay Vs Triac            01/01/70 00:00      
               multimeter is reading 'hold' current?            01/01/70 00:00      
               a simple "kick and hold" circuit            01/01/70 00:00      
                  RE: a simple "kick and hold" circuit            01/01/70 00:00      
                     Thanks            01/01/70 00:00      
                     no            01/01/70 00:00      
                        I see!            01/01/70 00:00      
                     You are absolutely right...            01/01/70 00:00      
                  What are the values of R and C ?            01/01/70 00:00      
                     To be calculated!            01/01/70 00:00      
                     About...            01/01/70 00:00      
               Here are some calculations ..might be helpful            01/01/70 00:00      
                  RE: some calculations            01/01/70 00:00      
                     To Andy            01/01/70 00:00      
                        current measurement            01/01/70 00:00      
                           Schematic            01/01/70 00:00      
                              Re-Drawn Schematic            01/01/70 00:00      
                                 ASCII Art            01/01/70 00:00      
                     Relay supply            01/01/70 00:00      
                  To Kiran            01/01/70 00:00      
               latching relay            01/01/70 00:00      
                  Latching relays are cost effective            01/01/70 00:00      
                     One thing to consider            01/01/70 00:00      
                        latching relay : status updated on bootup            01/01/70 00:00      
                           Ay be a mix will be fine            01/01/70 00:00      
                           I just found a relay which needs lot lesser current            01/01/70 00:00      
                           That's too late!            01/01/70 00:00      
                              My Circuit            01/01/70 00:00      
                                 But didn't you mention...            01/01/70 00:00      
                                    hot... depends            01/01/70 00:00      
                                       Agreed!            01/01/70 00:00      
                                          Thanks ALL.            01/01/70 00:00      
                                       Low voltage drop            01/01/70 00:00      
                                          Good luck!            01/01/70 00:00      
                              random phase?            01/01/70 00:00      
                                 The same what the manufacturer meant...            01/01/70 00:00      

Back to Subject List