Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
???
08/05/09 03:25
Read: times


 		 #168165 - Latching relays are cost effective
Responding to: ???'s previous message
I agree with Jan. Finally a simple suggestion.
If the number of operations over the engineered life of the product is within the relay specifications, then that is the optimum solution.
If the number of devices is small then the cost of device compared to development is not significant.
If the quantities are high then a 250V 10A device is available for < US$1.00. This is less than a solid state relay or a combination of triac, opto and associated components.
For about US$8,00 a latching relay can be designed to your specifications and that amount is refunded to you once you purchase > 500k units.

Good luck
Tony

List of 44 messages in thread
TopicAuthorDate
Mechnical Relay or Triac            01/01/70 00:00      
   Relays Or Triacs            01/01/70 00:00      
      Isolation            01/01/70 00:00      
      Relay or Triac            01/01/70 00:00      
         Pull-in vs hold current?            01/01/70 00:00      
         Relays Suggestions            01/01/70 00:00      
      Agree            01/01/70 00:00      
         optotriac            01/01/70 00:00      
            Relay Vs Triac            01/01/70 00:00      
               multimeter is reading 'hold' current?            01/01/70 00:00      
               a simple "kick and hold" circuit            01/01/70 00:00      
                  RE: a simple "kick and hold" circuit            01/01/70 00:00      
                     Thanks            01/01/70 00:00      
                     no            01/01/70 00:00      
                        I see!            01/01/70 00:00      
                     You are absolutely right...            01/01/70 00:00      
                  What are the values of R and C ?            01/01/70 00:00      
                     To be calculated!            01/01/70 00:00      
                     About...            01/01/70 00:00      
               Here are some calculations ..might be helpful            01/01/70 00:00      
                  RE: some calculations            01/01/70 00:00      
                     To Andy            01/01/70 00:00      
                        current measurement            01/01/70 00:00      
                           Schematic            01/01/70 00:00      
                              Re-Drawn Schematic            01/01/70 00:00      
                                 ASCII Art            01/01/70 00:00      
                     Relay supply            01/01/70 00:00      
                  To Kiran            01/01/70 00:00      
               latching relay            01/01/70 00:00      
                  Latching relays are cost effective            01/01/70 00:00      
                     One thing to consider            01/01/70 00:00      
                        latching relay : status updated on bootup            01/01/70 00:00      
                           Ay be a mix will be fine            01/01/70 00:00      
                           I just found a relay which needs lot lesser current            01/01/70 00:00      
                           That's too late!            01/01/70 00:00      
                              My Circuit            01/01/70 00:00      
                                 But didn't you mention...            01/01/70 00:00      
                                    hot... depends            01/01/70 00:00      
                                       Agreed!            01/01/70 00:00      
                                          Thanks ALL.            01/01/70 00:00      
                                       Low voltage drop            01/01/70 00:00      
                                          Good luck!            01/01/70 00:00      
                              random phase?            01/01/70 00:00      
                                 The same what the manufacturer meant...            01/01/70 00:00      

Back to Subject List