Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
???
04/27/07 12:55
Read: times


 		 #138114 - Values?
Responding to: ???'s previous message
Which resistor is R1, R2, and R3? I've got the caps figured out...

List of 53 messages in thread
TopicAuthorDate
Momentary toggle soft switch with flip-flop?            01/01/70 00:00      
   I don't like it.            01/01/70 00:00      
      How Bouncy            01/01/70 00:00      
         what good does 'minimum' do you            01/01/70 00:00      
   Schmidt trigger            01/01/70 00:00      
      Tricky...            01/01/70 00:00      
         rail to rail bounce            01/01/70 00:00      
      McKinney            01/01/70 00:00      
   4013 FF toggle circuit            01/01/70 00:00      
      Values?            01/01/70 00:00      
         Values of R1,R2 &R3? Look at PCB!            01/01/70 00:00      
            clocking a FF from an RC?            01/01/70 00:00      
               Agreed            01/01/70 00:00      
                  Follow the datsheet, that is design            01/01/70 00:00      
                  Why dismissing the flip-flop?            01/01/70 00:00      
                     dismissing the flip-flop?            01/01/70 00:00      
                        The CD4013 of Bruce's schematic            01/01/70 00:00      
                           The CD4013 of Bruce's schematic is shown as a f/f            01/01/70 00:00      
                              I answered to Bruce...            01/01/70 00:00      
                  The circuit shown,,,,            01/01/70 00:00      
                     Power Consumption            01/01/70 00:00      
   Overlooking the obvious?            01/01/70 00:00      
      Simpler?            01/01/70 00:00      
      Keymat            01/01/70 00:00      
   Why not a hard switch?            01/01/70 00:00      
      Requirements            01/01/70 00:00      
      Industrial designers is why            01/01/70 00:00      
         Fair enough!            01/01/70 00:00      
   Let The Microconroller Decide            01/01/70 00:00      
      dedicated microcontroller :-)            01/01/70 00:00      
      Interresting no flip-flop            01/01/70 00:00      
   dat is de bounce            01/01/70 00:00      
   The 4013 needs steep edges            01/01/70 00:00      
      caps            01/01/70 00:00      
      A Vauge Suggestion            01/01/70 00:00      
   additional parts            01/01/70 00:00      
      what pin of which chip in what package?            01/01/70 00:00      
         chip on drawing in generic post            01/01/70 00:00      
            slowig down the bugger is not going to make it clo            01/01/70 00:00      
   What about this?            01/01/70 00:00      
      what is 'SOFTSW"?            01/01/70 00:00      
      Seems OK Except...            01/01/70 00:00      
         nice to find a fellow "drawer of fuctions"            01/01/70 00:00      
            I find it eaasier to just...            01/01/70 00:00      
               We appreciate it            01/01/70 00:00      
      Further Analysis....            01/01/70 00:00      
      Would this work?            01/01/70 00:00      
      All comments noted            01/01/70 00:00      
   Round 3 - Hopefully better            01/01/70 00:00      
      Round 4 is the winner            01/01/70 00:00      
         Tomas?? Bruce?? Are you a schizo?            01/01/70 00:00      
            haha, yes            01/01/70 00:00      
         A bit confusing...            01/01/70 00:00      

Back to Subject List