| soft-start powersupply and controllers | | 01/01/70 00:00 |
| supervisor chip or processor with good brownout detection | | 01/01/70 00:00 |
| Per gives a good solution if you can tolerate restarts | | 01/01/70 00:00 |
| Long rise times of Vcc are critical! | | 01/01/70 00:00 |
| replace the 7805 | | 01/01/70 00:00 |
| Lot of information | | 01/01/70 00:00 |
| look at PowerTrends (TI) | | 01/01/70 00:00 |
| Some answers... | | 01/01/70 00:00 |
| Bigget reset capacitor and resistor | | 01/01/70 00:00 |
| it is NOT the capacitor value | | 01/01/70 00:00 |
| Thanks Erik | | 01/01/70 00:00 |
| I partially disagree | | 01/01/70 00:00 |
| disagree with what? | | 01/01/70 00:00 |
| With thinking only in a reset chip. | | 01/01/70 00:00 |
| Use the reset chip to reset the powersupply | | 01/01/70 00:00 |
| How about $0.15 | | 01/01/70 00:00 |
| A small clarification | | 01/01/70 00:00 |
| 3 pin regulators with uvlo | | 01/01/70 00:00 |
| Eh ? | | 01/01/70 00:00 |
| Only a clarification | | 01/01/70 00:00 |
| Steve, I meant turning on MCU supply | | 01/01/70 00:00 |
| and power down | | 01/01/70 00:00 |
| Erik, brown-out is handled by Silabs MCU!! | | 01/01/70 00:00 |
| Did I miss that? | | 01/01/70 00:00 |
| But Erik... | | 01/01/70 00:00 |
| In application notes, direct pull-ups have been used... | | 01/01/70 00:00 |
| some idiot, not there any more ... | | 01/01/70 00:00 |
| You seem to be wrong about the capacitor, Erik | | 01/01/70 00:00 |
| Not necessarily... | | 01/01/70 00:00 |
| the risetime has nothing to do with reset ... unless | | 01/01/70 00:00 |
| which SiLabs part? | | 01/01/70 00:00 |
| Andy.. | | 01/01/70 00:00 |
| SILabs urban legends | | 01/01/70 00:00 |
| Interesting... | | 01/01/70 00:00 |
| you may | | 01/01/70 00:00 |
| Thank you, I really appreciate it! | | 01/01/70 00:00 |
| Clarifying, Erik, Kai | | 01/01/70 00:00 |
| The reset from the supply monitor will be there | | 01/01/70 00:00 |
| Good advice... | | 01/01/70 00:00 |
I am guilty of not recalling all differences | | 01/01/70 00:00 |
| Only open-drain but not push-pull! | | 01/01/70 00:00 |
| Good one, Kai | | 01/01/70 00:00 |
| why the 'love' of the MAX1232? | | 01/01/70 00:00 |
| True, Erik | | 01/01/70 00:00 |
| Have you seen this post? | | 01/01/70 00:00 |
| Have you seen this post? | | 01/01/70 00:00 |
| Turn on your brain, Erik, and read what I wrote! | | 01/01/70 00:00 |
| a picture is worth 1000 words | | 01/01/70 00:00 |
| So you haven't read the words?? | | 01/01/70 00:00 |
| I was suggesting him the MAX1232... | | 01/01/70 00:00 |
| Well, even more demanding... | | 01/01/70 00:00 |
| Bigger, not bigget | | 01/01/70 00:00 |
| Only external electronics can help you | | 01/01/70 00:00 |
| Scheme to provide fast turn-on after full discharge | | 01/01/70 00:00 |
| Regulator with output enable | | 01/01/70 00:00 |
| You never exactly know what you get... | | 01/01/70 00:00 |
| Bypass caps | | 01/01/70 00:00 |
| Please don't stress this scheme too much... | | 01/01/70 00:00 |
