Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
???
07/02/09 15:12
Read: times


 		 #166665 - Interesting...
Responding to: ???'s previous message
Erik said:
I have 10thousands of boards working with the SILabs reset and a pullup resistor with no problems...

May I ask, what pull-up? And how do you power up your board? Fast turn-on from a truck battery via strobed switcher? (Is it this application you once told about? LED display in a bus?)

Kai

List of 58 messages in thread
TopicAuthorDate
soft-start powersupply and controllers            01/01/70 00:00      
   supervisor chip or processor with good brownout detection            01/01/70 00:00      
      Per gives a good solution if you can tolerate restarts            01/01/70 00:00      
   Long rise times of Vcc are critical!            01/01/70 00:00      
      replace the 7805            01/01/70 00:00      
         Lot of information            01/01/70 00:00      
            look at PowerTrends (TI)            01/01/70 00:00      
            Some answers...            01/01/70 00:00      
               Bigget reset capacitor and resistor            01/01/70 00:00      
                  it is NOT the capacitor value            01/01/70 00:00      
                     Thanks Erik            01/01/70 00:00      
                        I partially disagree            01/01/70 00:00      
                           disagree with what?            01/01/70 00:00      
                              With thinking only in a reset chip.            01/01/70 00:00      
                                 Use the reset chip to reset the powersupply            01/01/70 00:00      
                        How about $0.15            01/01/70 00:00      
                     A small clarification            01/01/70 00:00      
                        3 pin regulators with uvlo            01/01/70 00:00      
                        Eh ?            01/01/70 00:00      
                           Only a clarification            01/01/70 00:00      
                           Steve, I meant turning on MCU supply            01/01/70 00:00      
                        and power down            01/01/70 00:00      
                           Erik, brown-out is handled by Silabs MCU!!            01/01/70 00:00      
                              Did I miss that?            01/01/70 00:00      
                                 But Erik...            01/01/70 00:00      
                                    In application notes, direct pull-ups have been used...            01/01/70 00:00      
                                       some idiot, not there any more ...            01/01/70 00:00      
                                          You seem to be wrong about the capacitor, Erik            01/01/70 00:00      
                                             Not necessarily...            01/01/70 00:00      
                                             the risetime has nothing to do with reset ... unless            01/01/70 00:00      
                                             which SiLabs part?            01/01/70 00:00      
                                                Andy..            01/01/70 00:00      
                                                   SILabs urban legends            01/01/70 00:00      
                                                      Interesting...            01/01/70 00:00      
                                                         you may            01/01/70 00:00      
                                                            Thank you, I really appreciate it!            01/01/70 00:00      
                                                      Clarifying, Erik, Kai            01/01/70 00:00      
                                                         The reset from the supply monitor will be there            01/01/70 00:00      
                                                            Good advice...            01/01/70 00:00      
                                                               I am guilty of not recalling all differences            01/01/70 00:00      
                                                         Only open-drain but not push-pull!            01/01/70 00:00      
                                                            Good one, Kai            01/01/70 00:00      
                                                            why the 'love' of the MAX1232?            01/01/70 00:00      
                                                               True, Erik            01/01/70 00:00      
                                                                  Have you seen this post?            01/01/70 00:00      
                                                                     Have you seen this post?            01/01/70 00:00      
                                                                        Turn on your brain, Erik, and read what I wrote!            01/01/70 00:00      
                                                                           a picture is worth 1000 words            01/01/70 00:00      
                                                                              So you haven't read the words??            01/01/70 00:00      
                                                               I was suggesting him the MAX1232...            01/01/70 00:00      
      Well, even more demanding...            01/01/70 00:00      
   Bigger, not bigget            01/01/70 00:00      
   Only external electronics can help you            01/01/70 00:00      
   Scheme to provide fast turn-on after full discharge            01/01/70 00:00      
      Regulator with output enable            01/01/70 00:00      
         You never exactly know what you get...            01/01/70 00:00      
            Bypass caps            01/01/70 00:00      
               Please don't stress this scheme too much...            01/01/70 00:00      

Back to Subject List