Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
???
06/18/13 02:24
Read: times


 
#189949 - LP52
Responding to: ???'s previous message
I have just tested the software on an LP52. The consumption now drops to 0.6mA - much more reasonable.

The programming is flaky (again) though. Programming the LP52 using the AT89ISP adapter isn't really documented, in any documents I can find. I did manage to programme a chip, but verify fails and I can't erase the chip once it's programmed. But the software runs as intended at least...

Jim Granville said:
They do have a QFN variant, if you hit high volume production ?
Since you do not need all pins, you could make a relaxed QFN footprint,with only a few solder pads.

They have an exposed pad, that "should" be connected to ground. That will be hard on a single sided board :)
I think a TQFP footprint with some pads removed should work fine.

Mikkel

List of 44 messages in thread
TopicAuthorDate
Low-power MCU needed            01/01/70 00:00      
   OK, but wrong            01/01/70 00:00      
      Wrong how?            01/01/70 00:00      
         Silabs options            01/01/70 00:00      
            C8051F99x            01/01/70 00:00      
               Silabs            01/01/70 00:00      
                  look it up            01/01/70 00:00      
                     Looked up            01/01/70 00:00      
                        f53, no            01/01/70 00:00      
                        C8051F537A is OK            01/01/70 00:00      
         the current in active mode is not the issue            01/01/70 00:00      
            Inactive current            01/01/70 00:00      
         re: wrong            01/01/70 00:00      
            Consumers            01/01/70 00:00      
   Zilog Z51F0410             01/01/70 00:00      
      Zilog            01/01/70 00:00      
   Check you are entering idle ?            01/01/70 00:00      
   idle current            01/01/70 00:00      
      Idle test            01/01/70 00:00      
         re:            01/01/70 00:00      
            It floats! It floats!            01/01/70 00:00      
               re:floats            01/01/70 00:00      
               re:floats            01/01/70 00:00      
                  Timers            01/01/70 00:00      
         More idle tests            01/01/70 00:00      
            Better regulator?            01/01/70 00:00      
               LR8K4 450V regulator             01/01/70 00:00      
         also try CLKREG            01/01/70 00:00      
            Clk Dividers are a good idea            01/01/70 00:00      
               No dividers            01/01/70 00:00      
                  LP52 is cheaper too...            01/01/70 00:00      
                     LP52            01/01/70 00:00      
                        No GND pin?            01/01/70 00:00      
         re:idle            01/01/70 00:00      
         Totally idle            01/01/70 00:00      
            Checks            01/01/70 00:00      
               More checks            01/01/70 00:00      
                  Power Down ?            01/01/70 00:00      
                  test setup            01/01/70 00:00      
   STC            01/01/70 00:00      
      C8051F86x/85x ?            01/01/70 00:00      
      Maybe not such a good choice, after all?            01/01/70 00:00      
         Support?            01/01/70 00:00      
            '51 support            01/01/70 00:00      

Back to Subject List