Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
???
03/06/06 12:29
Read: times


 		 #111349 - 8 reed SW parallely + 21.12A / at 12VDC
Responding to: ???'s previous message
kai klass said:

Inrush peak current is about 8.8 times higher than rated DC-current!


so, for my case it's going to be about .3 * 8.8 = 2.64A

Kindly use the link below to see the circuit i have designed for testing the reed switch for its ability to withstand the in rush current.

http://www.8052.com/users/Sur...switch.pdf

with this ckt, i have planned to test 8 reed switches (driving through port1.0 -1.7)in a sequential manner( with each switch turning ON with 2 sec delay after the previous switch completes its operation)to make the LM 338 (used as the voltage source) sustain the inrush current.

but i would like to know for any other method other than using a micro.

mainly, i need to test 8 switches parallely(2.64A * 8 = 21.12A / at 12VDC will be taken from the source when operated parallely). but not sure of how to use an appropriate power source to do that.
your suggestions could be highly helpful.

thanking you,
suresh.



List of 57 messages in thread
TopicAuthorDate
inrush current + suitable voltage sour            01/01/70 00:00      
   Inrush current of lamp            01/01/70 00:00      
      Current inrush            01/01/70 00:00      
         NTC?            01/01/70 00:00      
            Soft-start            01/01/70 00:00      
               8 reed SW parallely + 21.12A / at 12VDC            01/01/70 00:00      
                  Car battery???            01/01/70 00:00      
                  inrush current            01/01/70 00:00      
                  totally irrelevant            01/01/70 00:00      
                  No testing needed, standardly            01/01/70 00:00      
                     replies            01/01/70 00:00      
                        Reply to "replies"            01/01/70 00:00      
                           the difference between "cheap" and "inex            01/01/70 00:00      
                           current limit resistor            01/01/70 00:00      
                              are you just grasping for straws?            01/01/70 00:00      
            NTC, yes            01/01/70 00:00      
               Filaments            01/01/70 00:00      
                  In the days of radios for AC and DC            01/01/70 00:00      
                     Thanks            01/01/70 00:00      
            resistor parallel to Switch!            01/01/70 00:00      
               MOSFET, constant current source?            01/01/70 00:00      
                  not for my use            01/01/70 00:00      
                     Ok, but...            01/01/70 00:00      
                        but i think            01/01/70 00:00      
                           Relays            01/01/70 00:00      
                              yes ofcourse            01/01/70 00:00      
                                 here we go again            01/01/70 00:00      
                                    Even more!!            01/01/70 00:00      
                                       werlcome to the club            01/01/70 00:00      
                                       reply            01/01/70 00:00      
                                          why did you not say so?            01/01/70 00:00      
                                          You made a fool of us!            01/01/70 00:00      
                                             reply            01/01/70 00:00      
                                                That's no fun!            01/01/70 00:00      
                                                   Suresh, I hope you had fun            01/01/70 00:00      
                                                   reply            01/01/70 00:00      
                                                      yeah 6 days later.            01/01/70 00:00      
                  Hello Kai,            01/01/70 00:00      
                     Look at here            01/01/70 00:00      
                        Thank you very much Kai.            01/01/70 00:00      
                           It just strikes me            01/01/70 00:00      
                              yes you are right            01/01/70 00:00      
                                 Reed switch problems            01/01/70 00:00      
                                    Current rating?            01/01/70 00:00      
                                       I recall long ago something about a "sti            01/01/70 00:00      
                                       Reed problem            01/01/70 00:00      
                                          Glueing together            01/01/70 00:00      
                                             Reed problems            01/01/70 00:00      
                                                reed relayrs            01/01/70 00:00      
                           power dissipation calculations?            01/01/70 00:00      
                              bulb voltage drop            01/01/70 00:00      
                                 Thanks            01/01/70 00:00      
                                 (.2*bulb resistance            01/01/70 00:00      
                                    The bulb            01/01/70 00:00      
                              Constant current during inrush moment            01/01/70 00:00      
                                 Thanks a lot Kai            01/01/70 00:00      
         Choke would be huge            01/01/70 00:00      

Back to Subject List