Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
???
09/28/06 03:37
Read: times


 		 #125241 - Chips are already soldered onto the board
Responding to: ???'s previous message
Thanks, for your suggestions, Joseph!

The chips are already soldered onto the board. I think I could take a milling machine with a metal eraser, like dental technicians use for their work. I should be able to connect the machine to signal ground of board somehow, so that the metal eraser cannot float too much. I could put a bit of water onto the package surface also, forming a water film, like Hal already mentioned, so that ESD cannot develop at all.

Kai

List of 45 messages in thread
TopicAuthorDate
How to remove the stamp from chip package?            01/01/70 00:00      
   paint the chip            01/01/70 00:00      
      Can be removed?            01/01/70 00:00      
         I am afraid...            01/01/70 00:00      
            more ideas            01/01/70 00:00      
               Yes, but...            01/01/70 00:00      
                  let me elaborate on the idea...            01/01/70 00:00      
            If its a ceramic package            01/01/70 00:00      
               Thanks            01/01/70 00:00      
            Yes..            01/01/70 00:00      
               epoxy            01/01/70 00:00      
                  Thanks!            01/01/70 00:00      
                     ESD and bead blasting            01/01/70 00:00      
                        Chips are already soldered onto the board            01/01/70 00:00      
                           Not BGA            01/01/70 00:00      
                              Thanks, Joseph!            01/01/70 00:00      
                  Formic acid doesn't work for me!            01/01/70 00:00      
               epoxy or novalac            01/01/70 00:00      
                  Yes, high tech epoxy...            01/01/70 00:00      
         some paint works            01/01/70 00:00      
            Yes, that's what I'm looking for!            01/01/70 00:00      
   Stamp?            01/01/70 00:00      
      marking            01/01/70 00:00      
      The printing on the package, the marking            01/01/70 00:00      
         Sand paper, cloth emery sheet            01/01/70 00:00      
            Thanks            01/01/70 00:00      
               How about very fine grit emery cloth damp or wet?            01/01/70 00:00      
                  Yes, this is a good idea!            01/01/70 00:00      
                     Methy-Ethyl Ketone Peroxide?            01/01/70 00:00      
                        Plastic            01/01/70 00:00      
                        MEKP            01/01/70 00:00      
   I remember that situation ...            01/01/70 00:00      
      abrasive and ESD            01/01/70 00:00      
      back in the old days ...            01/01/70 00:00      
         I may be being stupid but...            01/01/70 00:00      
            there are reasons ...            01/01/70 00:00      
               Always a pleasure            01/01/70 00:00      
         While in memory lane...            01/01/70 00:00      
            We did that at IBM, too.            01/01/70 00:00      
            Special companies do it            01/01/70 00:00      
               You can get stock numbers on anything            01/01/70 00:00      
   Use a Dremel            01/01/70 00:00      
      It's important they don't notice it!            01/01/70 00:00      
         It didn't blister            01/01/70 00:00      
      I will have a look at it            01/01/70 00:00      

Back to Subject List