Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
???
03/02/06 09:07
Read: times


 		 #111039 - after the set delay Time
Responding to: ???'s previous message
Kai Klaas said:

Have a look at figure 4 of

http://www.fairchildsemi.com/ds/NE%2FNE555.pdf

again, to see what condition must be met, to cause abnormal triggering: It's a logic low level at trigger input (pin2 of TLC555) at the end of monoflop pulse, before the monoflop pulse was ended!
Kai

Yes . i understood the precision that could be achieved during the delay.
Then, is it that i dont need to worry about the switch being pressed continuously after the set delay?
eg : if i set the delay as .5sec or less (BC550 will do its job only for this time) and pressing the switch continuously for 1 sec. will it not cause any abnormality or a repeat in cycle?

suresh.




List of 39 messages in thread
TopicAuthorDate
Pressing 555 trigger SW continuously.            01/01/70 00:00      
   Again            01/01/70 00:00      
   capacitor couple it.            01/01/70 00:00      
      Re: cap coupling            01/01/70 00:00      
         Look up the internal block diagram            01/01/70 00:00      
            Read the Data Sheet!!            01/01/70 00:00      
      got the o/p            01/01/70 00:00      
         Satisfaction            01/01/70 00:00      
            Thanku steve            01/01/70 00:00      
         Not enough            01/01/70 00:00      
            alternatives ?            01/01/70 00:00      
               Remedy            01/01/70 00:00      
                  remedy?            01/01/70 00:00      
                     Alternatives            01/01/70 00:00      
                  BC550 & diodes            01/01/70 00:00      
                     Try it by yourself, it's simple!            01/01/70 00:00      
                        analysis results            01/01/70 00:00      
                           Analysis            01/01/70 00:00      
                              Thank you            01/01/70 00:00      
                              after the set delay Time            01/01/70 00:00      
                                 Enhanced debouncing            01/01/70 00:00      
                                    What do you think about it, Suresh?            01/01/70 00:00      
   why the neqw thread            01/01/70 00:00      
      reply            01/01/70 00:00      
         Read the Data Sheet!!            01/01/70 00:00      
   kalpak dabir            01/01/70 00:00      
   Have you considered using a 74121?            01/01/70 00:00      
      74121 versus CMOS555            01/01/70 00:00      
      74121 fine for short period delays?            01/01/70 00:00      
         No debounce needed???            01/01/70 00:00      
            Schmitt trigger operation?            01/01/70 00:00      
               Transition times of input signal            01/01/70 00:00      
                  controlling noise related issues            01/01/70 00:00      
                     Schmitt-trigger operation            01/01/70 00:00      
                      CD 4541BC = Alternative for ICM 7555?            01/01/70 00:00      
                        Do you really need to build it?            01/01/70 00:00      
                           Yes.            01/01/70 00:00      
                              try try try again            01/01/70 00:00      
                                 a sign of confidence            01/01/70 00:00      

Back to Subject List