Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
???
02/07/06 11:28
Read: times


 		 #109376 - Instruction Description
Responding to: ???'s previous message
Kai Klaas said:
Save This Code
begin:              mov auxr,#00011001b     ;reset pin is input

Suresh R said:
description of this instruction is needed

Each and every instruction in the 8051 Instruction Set is described in detail in the following document:

80C51 Family Programmer’s Guide and Instruction Set:
http://www.semiconductors.philips.com/acrobat/v...UIDE_1.pdf

Yes - that's Chapter 2 of the so-called "bible" for the 8051; the other important chapters are:

Chapter 1 - 80C51 Family Architecture:
http://www.semiconductors.philips.com/acrobat/v...ARCH_1.pdf

Chapter 3 - 80C51 Family Hardware Description:
http://www.semiconductors.philips.com/acrobat/v...WARE_1.pdf

List of 57 messages in thread
TopicAuthorDate
Circuit for dispensing unit            01/01/70 00:00      
   1.1 sec monoshot            01/01/70 00:00      
      this thread is apin off from an earlier            01/01/70 00:00      
         yes            01/01/70 00:00      
         timing circuit            01/01/70 00:00      
   Monostable            01/01/70 00:00      
   Yes.            01/01/70 00:00      
   Hello All            01/01/70 00:00      
      Description of the "Dispensing Unit"            01/01/70 00:00      
         using micro            01/01/70 00:00      
            Microcontroller            01/01/70 00:00      
               Pressure            01/01/70 00:00      
            What must your circuit can do?            01/01/70 00:00      
               0.1 sec            01/01/70 00:00      
                  but not with a potentiometer            01/01/70 00:00      
                     Vernier            01/01/70 00:00      
                        and calibrate it how?            01/01/70 00:00      
               Precision            01/01/70 00:00      
                  Sure!            01/01/70 00:00      
                     Price            01/01/70 00:00      
                        Less than 1€            01/01/70 00:00      
                           levels of precision            01/01/70 00:00      
                              Please have a look into datasheet!            01/01/70 00:00      
                                 somewhere here there is a link            01/01/70 00:00      
                                    Details?            01/01/70 00:00      
                                       I recall that in an earlier thread            01/01/70 00:00      
                              Ooops.            01/01/70 00:00      
                              Blown Discharge PIN            01/01/70 00:00      
                                 You can also let the smoke out of the            01/01/70 00:00      
                                    limits            01/01/70 00:00      
                                       dissapation            01/01/70 00:00      
                                          There must be a point.            01/01/70 00:00      
                                             Fusing the bonding wires            01/01/70 00:00      
                                                History making            01/01/70 00:00      
                                                Current limiting            01/01/70 00:00      
                                 I do go through            01/01/70 00:00      
            schematic and code            01/01/70 00:00      
               codes            01/01/70 00:00      
                  Instruction Description            01/01/70 00:00      
                     not quite            01/01/70 00:00      
                        Pedantic            01/01/70 00:00      
                           is that not the pot calling the kettle b            01/01/70 00:00      
                              Of course not!            01/01/70 00:00      
                  Answers            01/01/70 00:00      
                     Re: codes and shcematic            01/01/70 00:00      
                        Recommendations            01/01/70 00:00      
                           Decimal switches - how to start C            01/01/70 00:00      
      LM555 pin 2 wired wrong.            01/01/70 00:00      
         ... and the LED?            01/01/70 00:00      
            i'm sure thts not the circuit            01/01/70 00:00      
            Astable??            01/01/70 00:00      
               I wondered who'd spot that first...            01/01/70 00:00      
   Damaged?            01/01/70 00:00      
      And Andy's correction            01/01/70 00:00      
         Absolutely!            01/01/70 00:00      
   one shot in the foot            01/01/70 00:00      
      Need not to work unreliably            01/01/70 00:00      

Back to Subject List