Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
???
02/01/06 05:23
Read: times


 		 #108855 - Hello All
Responding to: ???'s previous message
Suresh R said:
Hello Kai,
I connected a monostable circuit (with LM555cn) but with the constant values of R &C (just to check how it works!)
I used a 100K/.25W resistor with 10uF/25V cap(electrolytic). An LED at the o/p.

But when i triggered, the LED is not flikering!!!
It remains in the 'ON' state continuously.

Could the RC components i choosed (especially 'Cap'- electrolytic) may lead to such an o/p?

-suresh.




Hello All,
Kindly use the link given below to see the description this new thread.

http://www.8052.com/forumchat/read.phtml?id=108597

Thanking you,
-suresh.

List of 57 messages in thread
TopicAuthorDate
Circuit for dispensing unit            01/01/70 00:00      
   1.1 sec monoshot            01/01/70 00:00      
      this thread is apin off from an earlier            01/01/70 00:00      
         yes            01/01/70 00:00      
         timing circuit            01/01/70 00:00      
   Monostable            01/01/70 00:00      
   Yes.            01/01/70 00:00      
   Hello All            01/01/70 00:00      
      Description of the "Dispensing Unit"            01/01/70 00:00      
         using micro            01/01/70 00:00      
            Microcontroller            01/01/70 00:00      
               Pressure            01/01/70 00:00      
            What must your circuit can do?            01/01/70 00:00      
               0.1 sec            01/01/70 00:00      
                  but not with a potentiometer            01/01/70 00:00      
                     Vernier            01/01/70 00:00      
                        and calibrate it how?            01/01/70 00:00      
               Precision            01/01/70 00:00      
                  Sure!            01/01/70 00:00      
                     Price            01/01/70 00:00      
                        Less than 1€            01/01/70 00:00      
                           levels of precision            01/01/70 00:00      
                              Please have a look into datasheet!            01/01/70 00:00      
                                 somewhere here there is a link            01/01/70 00:00      
                                    Details?            01/01/70 00:00      
                                       I recall that in an earlier thread            01/01/70 00:00      
                              Ooops.            01/01/70 00:00      
                              Blown Discharge PIN            01/01/70 00:00      
                                 You can also let the smoke out of the            01/01/70 00:00      
                                    limits            01/01/70 00:00      
                                       dissapation            01/01/70 00:00      
                                          There must be a point.            01/01/70 00:00      
                                             Fusing the bonding wires            01/01/70 00:00      
                                                History making            01/01/70 00:00      
                                                Current limiting            01/01/70 00:00      
                                 I do go through            01/01/70 00:00      
            schematic and code            01/01/70 00:00      
               codes            01/01/70 00:00      
                  Instruction Description            01/01/70 00:00      
                     not quite            01/01/70 00:00      
                        Pedantic            01/01/70 00:00      
                           is that not the pot calling the kettle b            01/01/70 00:00      
                              Of course not!            01/01/70 00:00      
                  Answers            01/01/70 00:00      
                     Re: codes and shcematic            01/01/70 00:00      
                        Recommendations            01/01/70 00:00      
                           Decimal switches - how to start C            01/01/70 00:00      
      LM555 pin 2 wired wrong.            01/01/70 00:00      
         ... and the LED?            01/01/70 00:00      
            i'm sure thts not the circuit            01/01/70 00:00      
            Astable??            01/01/70 00:00      
               I wondered who'd spot that first...            01/01/70 00:00      
   Damaged?            01/01/70 00:00      
      And Andy's correction            01/01/70 00:00      
         Absolutely!            01/01/70 00:00      
   one shot in the foot            01/01/70 00:00      
      Need not to work unreliably            01/01/70 00:00      

Back to Subject List