Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
???
07/18/11 09:04
Read: times


 		 #182880 - Constructing a component..
Responding to: ???'s previous message
In the CAD software tool you will need to create your "jumper pad" as a component. Define it as a two terminal component. Do likewise within your schematic package and then include the necessary instances of JP1, JP2 ... etc etc. This will allow the components to be net listed out of the schematic and imported into the CAD layout package in a manner as all the other components.

Designing the special pad can take some work to get it all correct. You have to remember to specify that this "component" will only have a pad on one side of the board. When you create the pad stack also remember to leave an opening in the solder mask so it is possible to solder on the site.

Each CAD package has its own little quirks and special procedures to get free formed copper items included into the pad definition.

Michael Karas

List of 43 messages in thread
TopicAuthorDate
PAD as Jumper            01/01/70 00:00      
   Make It Like...            01/01/70 00:00      
      Snake eating snake ;)            01/01/70 00:00      
   Constructing a component..            01/01/70 00:00      
      clue needed            01/01/70 00:00      
         Altium designer forum            01/01/70 00:00      
         Component            01/01/70 00:00      
            The "Component" has 2 pads.            01/01/70 00:00      
               It is quite common ...            01/01/70 00:00      
                  Common practice, ...            01/01/70 00:00      
                     perspective?            01/01/70 00:00      
                        My perspective            01/01/70 00:00      
                           fine table, i just have to add            01/01/70 00:00      
                              technically proficient installers            01/01/70 00:00      
                                 That is not how I think            01/01/70 00:00      
                                    A soldier jump            01/01/70 00:00      
                                 Not for field configuration            01/01/70 00:00      
                                    But Dev Boards            01/01/70 00:00      
                                       RE: But Dev Boards            01/01/70 00:00      
   Another possibility to consider....            01/01/70 00:00      
   Some other ideas from the web            01/01/70 00:00      
      that final picture            01/01/70 00:00      
         original page reference            01/01/70 00:00      
            Another Example Linking Picture            01/01/70 00:00      
               I get the red box again!            01/01/70 00:00      
                  Red Box Indeed...            01/01/70 00:00      
                  Trivial setting, but sometimes quite needed            01/01/70 00:00      
      Going the other way            01/01/70 00:00      
         Removing a Link            01/01/70 00:00      
            You misunderstand            01/01/70 00:00      
               I did misunderstand....            01/01/70 00:00      
      The Whole Point...            01/01/70 00:00      
   PAD as Jumper            01/01/70 00:00      
      Narrow, pointy bits            01/01/70 00:00      
      Isn't that a touch sensor?            01/01/70 00:00      
         PAD as jumper            01/01/70 00:00      
            same comment            01/01/70 00:00      
            Use This            01/01/70 00:00      
               PAD as Jumper            01/01/70 00:00      
                  Narrow Gap            01/01/70 00:00      
   PAD as Jumper/Short link            01/01/70 00:00      
      What "problem" ?            01/01/70 00:00      
      CAD software has lots of primitives            01/01/70 00:00      

Back to Subject List