Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
???
07/16/10 11:53
Read: times


 		 #177320 - always possible to machine solder at near 100% yield
Responding to: ???'s previous message
Not sure if he was talking about a manufacturer.

All chips should be possible to solder with 99.9... percent yield when machine-soldered in a calibrated process.

But some chips can be very hard or almost impossible to hand-solder. Anything that has pads or balls under the chip quickly makes it hard to hand-solder. In some situations hot air can be used, but that is not always enough.

Maybe he was talking about a company that did hand-soldering of prototypes or manual replacements of chips?

List of 44 messages in thread
TopicAuthorDate
USB to IIC cable            01/01/70 00:00      
   http://i2cchip.com/ ?            01/01/70 00:00      
   FTDI?            01/01/70 00:00      
   Proper test tools            01/01/70 00:00      
   clarification            01/01/70 00:00      
      no, I have no experience with what I wrote above            01/01/70 00:00      
      TotoalPhase - Aardvark            01/01/70 00:00      
         Aardvark            01/01/70 00:00      
            That should be harmless            01/01/70 00:00      
               Unless you're an ant or termite            01/01/70 00:00      
            Aardvark Today            01/01/70 00:00      
         could you explain a bit further            01/01/70 00:00      
            Re: could you explain a bit further            01/01/70 00:00      
         Aardvark....            01/01/70 00:00      
      I have used MCC            01/01/70 00:00      
         Now I used it            01/01/70 00:00      
   without IC            01/01/70 00:00      
      "easy" ?            01/01/70 00:00      
         No need IC            01/01/70 00:00      
         like this            01/01/70 00:00      
            can (peobably) be done, but            01/01/70 00:00      
            Not a great idea!            01/01/70 00:00      
               "Microcontrollers with USB and I2C are now common"            01/01/70 00:00      
                  elaborating            01/01/70 00:00      
            Bit Bang on Serial Port            01/01/70 00:00      
               my opinion expressed by editing the above            01/01/70 00:00      
               remote area..            01/01/70 00:00      
                  No USB without USB protocol            01/01/70 00:00      
                     with minimum MCU            01/01/70 00:00      
                        Forget about it - no bitbanged USB!            01/01/70 00:00      
                        Additonal Comments            01/01/70 00:00      
                           budget and stock            01/01/70 00:00      
                              Silabs C8051F326            01/01/70 00:00      
                                 the package            01/01/70 00:00      
                                    ease of soldering            01/01/70 00:00      
                                       re: ease of soldering            01/01/70 00:00      
                                          handmade            01/01/70 00:00      
                                          Good yield            01/01/70 00:00      
                                             always possible to machine solder at near 100% yield            01/01/70 00:00      
                                                Important proviso            01/01/70 00:00      
                                             Better subcontractor            01/01/70 00:00      
                           found but..            01/01/70 00:00      
                              Found what?            01/01/70 00:00      
                                 reffering            01/01/70 00:00      

Back to Subject List