Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
???
01/04/12 16:56
Read: times


 		 #185303 - Code indented
Responding to: ???'s previous message
Save filename.txt
************************************************************************ 

PCF1_ADD EQU 01000101b ; I2C expander 1 
PCF2_ADD EQU 01001101b ; I2C expander 2 

RES_1 EQU 0x00 ; 100k ohms 
RES_2 EQU 0x01 ; 10k ohms  these are integer values for 2-bit select lines 
RES_3 EQU 0x02 ; 1k ohm 
RES_4 EQU 0x03 ; 0.1k ohms 

BYE_BITS DATA 0x40 ; 8-bit register for counting down 8 units 
MUX_NO DATA 0x41 ; 8-bit register for holding an ID number 

NACK BIT 0x50 ; Acknowledge flag for I2C 
PCF_2 BIT 0x51 ; I2C expander select flag 

************************************************************************ 


 



Here is the code indented,..

List of 40 messages in thread
TopicAuthorDate
Assembly coding micro-converters            01/01/70 00:00      
   Code indented            01/01/70 00:00      
      Assemblers often have different syntax            01/01/70 00:00      
         Assembler            01/01/70 00:00      
            Why not use Keil A51 ?            01/01/70 00:00      
               why assembler?            01/01/70 00:00      
                  Libraries?!?!?            01/01/70 00:00      
                     Libraries good, but not always best            01/01/70 00:00      
                        Ok back to Data and Bit            01/01/70 00:00      
                           Manual            01/01/70 00:00      
                           ok back            01/01/70 00:00      
                              I C            01/01/70 00:00      
               Keil A51            01/01/70 00:00      
                  junk downloaders            01/01/70 00:00      
                  take a look at ASEM51            01/01/70 00:00      
                     asem-51 macros            01/01/70 00:00      
                        You don't have to use 'em            01/01/70 00:00      
                  re-think about tools            01/01/70 00:00      
                     ADuC842            01/01/70 00:00      
                        learn            01/01/70 00:00      
                           There are PLENTY of debuggers ...            01/01/70 00:00      
                              Documentation            01/01/70 00:00      
                                 interrupt vectors            01/01/70 00:00      
                                 Memo to Reinhard Keil            01/01/70 00:00      
                                 Keil docs are not bad.            01/01/70 00:00      
                                 Well ... Last time I had questions about ASEM51 ...            01/01/70 00:00      
                                    the good and the bad            01/01/70 00:00      
                                       Well, I must have mistyped            01/01/70 00:00      
                                          asem/asm            01/01/70 00:00      
                                          linker support?            01/01/70 00:00      
                                             it's provided by ASEM-51, I suppose            01/01/70 00:00      
   Ok back to the task at hand            01/01/70 00:00      
      make it easy for yourself            01/01/70 00:00      
         I’m afraid the hard ware is non negotiable            01/01/70 00:00      
            well, ....            01/01/70 00:00      
               Dinosours, I2Cs, Gang-bang???            01/01/70 00:00      
                  1st            01/01/70 00:00      
                     Simple approach            01/01/70 00:00      
                        yes            01/01/70 00:00      
                           For Free :-)            01/01/70 00:00      

Back to Subject List