Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
???
10/19/10 22:59
Read: times


 		 #179201 - I leave it to you
Responding to: ???'s previous message
One pin to led's anode and then other side is from resistor 330R to ground.

I leave it to you to verify with tha datasheet that both codes configure the LED pin as push-pull which will be required with the LED connected that way

Erik



List of 49 messages in thread
TopicAuthorDate
p89lpc936 keil programming help required.            01/01/70 00:00      
   magic code?            01/01/70 00:00      
      mov 0A5H,#0FFH            01/01/70 00:00      
   a glaring difference            01/01/70 00:00      
      a glaring difference            01/01/70 00:00      
         what happens if            01/01/70 00:00      
            what happens if            01/01/70 00:00      
               BiDir or PushPull            01/01/70 00:00      
               I leave it to you            01/01/70 00:00      
                  magic code?            01/01/70 00:00      
                  I leave it to you            01/01/70 00:00      
                     1) formatted, 2)commented, 3) correct            01/01/70 00:00      
                        1) formatted, 2)commented, 3) correct            01/01/70 00:00      
                           it is STILL two different things            01/01/70 00:00      
                              Apples and Orange Juice            01/01/70 00:00      
                                 Please focus on the problem i have            01/01/70 00:00      
                                    Software delay loop in C is a no-no            01/01/70 00:00      
                                       Software delay loop in C is a no-no            01/01/70 00:00      
                                          Reduce problem into smaller problems            01/01/70 00:00      
                                             Reduce problem into smaller problems            01/01/70 00:00      
                                             Simulator vs real hardware            01/01/70 00:00      
                                             Current limits            01/01/70 00:00      
                                             Per Westermark's previous message            01/01/70 00:00      
                                                Delay speed            01/01/70 00:00      
                                                   Elaborate            01/01/70 00:00      
                                                      tried 5 for the '51 and Keil won            01/01/70 00:00      
                                    the problem you have is ...            01/01/70 00:00      
                                       the problem you have is ...            01/01/70 00:00      
                                          do you have LEDs connected to the simulator?            01/01/70 00:00      
                                          not executing on actual hardware while simulator is fine            01/01/70 00:00      
                                    Oh So Focused            01/01/70 00:00      
   Double-post            01/01/70 00:00      
   Are you using the limited version of KEIL? the for loop....            01/01/70 00:00      
      valid C            01/01/70 00:00      
         Thats the point            01/01/70 00:00      
            nope            01/01/70 00:00      
               I wouldnt trust it            01/01/70 00:00      
                  if you do not trust it ....            01/01/70 00:00      
               And if you trust it so much why doesnt it work?            01/01/70 00:00      
                  And if you trust it so much why doesnt it work?            01/01/70 00:00      
                     trust, yes, but knowledge also required            01/01/70 00:00      
                  wait call + assumptions about two-complement, ...            01/01/70 00:00      
                     The C Standard            01/01/70 00:00      
                        who is "you"?            01/01/70 00:00      
            Yes, you can!            01/01/70 00:00      
      Quite common loop design for bit operations            01/01/70 00:00      
      for( expression-1; expression-2; expression-3 ) [ed]            01/01/70 00:00      
         erratum            01/01/70 00:00      
            Corrigendum            01/01/70 00:00      

Back to Subject List