Email: Password: Remember Me | Create Account (Free)

Back to Subject List

Old thread has been locked -- no new posts accepted in this thread
???
04/17/11 15:52
Modified:
  04/17/11 16:00
Read: times


 		 #181930 - I have said this in the first post
Responding to: ???'s previous message
Kai Klaas said:
Mehdi said:
I have Received 40 Khz signal with this sensor from Ir Remote Control with less than 5 usecond rise and fall times,

So, this is your signal? The amplitude is 0,5Vss and the signal is sitting on an offset of 8,5V? Then, why not treating the signal as AC-signal? The offset could be filtered out by a simple high pass filter.


It is true,but assume you want to calibrate the scanner in the steady state,
so ac coupling can't work,

List of 42 messages in thread
TopicAuthorDate
Signal Conditioning!            01/01/70 00:00      
   AC-coupling don't work to 0Hz and kills DC info            01/01/70 00:00      
      subtracting 8.4V            01/01/70 00:00      
         Also question if 8.5V is guaranteed lowest input.            01/01/70 00:00      
            Is Instrumentation Amplifier is good choise?            01/01/70 00:00      
               Instrumentation Amplifier or op-amp            01/01/70 00:00      
                  Thanks Erik            01/01/70 00:00      
   A scheme using the OP-27...            01/01/70 00:00      
      Kai,You are always Positive!            01/01/70 00:00      
      Another scheme...            01/01/70 00:00      
         Take care with OPA2743...            01/01/70 00:00      
            Thanks Again Kai            01/01/70 00:00      
         -5 Volt Supply            01/01/70 00:00      
            Again            01/01/70 00:00      
               Wrong            01/01/70 00:00      
                  No,only 2 questions!            01/01/70 00:00      
                     Two answers...            01/01/70 00:00      
                        Thank you very much dear Kai            01/01/70 00:00      
         a question?            01/01/70 00:00      
      Please Tell Me your Comments!            01/01/70 00:00      
         ?            01/01/70 00:00      
            Yes,kai            01/01/70 00:00      
               Differential signaling            01/01/70 00:00      
                  Some Questions!            01/01/70 00:00      
                     Precision            01/01/70 00:00      
                        Thanks Per,            01/01/70 00:00      
                     Some answers...            01/01/70 00:00      
                        factor of 4            01/01/70 00:00      
                           Don't forget the subtracting scheme!            01/01/70 00:00      
                        kindness            01/01/70 00:00      
                        Deduction!            01/01/70 00:00      
                           Correct            01/01/70 00:00      
                        nature of signal!            01/01/70 00:00      
                           I'm sorry?            01/01/70 00:00      
                              A bit more            01/01/70 00:00      
                                 This is your signal?            01/01/70 00:00      
                                    I have said this in the first post            01/01/70 00:00      
                                       Any link?            01/01/70 00:00      
                                          calibrating,            01/01/70 00:00      
                           Is there a datasheet in english?            01/01/70 00:00      
                              No,i have searched very much            01/01/70 00:00      
            DYNAMIC RESPONSE            01/01/70 00:00      

Back to Subject List